Dealer Locator

Products

18 Bale Edge

Features:

The 18 Bale Edge System arranges the bales on edge 6 wide and 3 long.
  • Our largest bale system.
  • Good for filling van trailers from the rear.
  • Handles bales from 32” to 44” long
  • Bundle dimensions are 84” wide and 96” to 132” long
  • The 18 Bale Edge System has a 17% time savings advantage over the 15 bale as the grab contains 20% more bales, it reduces the number of packs by 17%.
  • This bale arrangement allows you to completely fill your 9’x24′ wagon.
  • Loader with at least 2200 lb lift capacity

Works With:

15 Bale Edge

Features:

The 15 Bale Edge System arranges the bales on edge 5 wide and 3 long.
  • Handles Bales from 32” to 44” long
  • Bundle dimensions are 70” wide by 96” to 132” long
  • This bale system arrangement allows you to completely fill your 9’x20′ wagon.
  • The 15 Bale Edge System pack has a 33% time savings advantage over the 10 bale as the grab contains 50% more bales, it reduces the number of packs by 33%.
  • Loader with at least 1900 lb lift capacity

Works With:

10 Bale Edge

Features:

The 10 Bale Edge System arranges the bales on edge 5 wide and 2 long.
  • Handles bales from 32” to 48” long
  • Bundle dimensions are 70” wide and 64” to 96” long
  • The 10 Bale Edge System is well suited for small farms.
  • The low weight requirement for the grabber allows for the use of a smaller loader.
  • If your bales are 36″ long, you can cross stack the bales with the KN510 or 510 grabber.
  • Loader with at least 1500 lb lift capacity

Works With:

15 Bale Flat

Features:

The 15 Bale Flat System arranges the bales on their strings 5 wide and 3 long.
  • Our largest Bale Flat System configuration for bales on their strings.
  • Handles bales from 32” to 44” long
  • Bundle dimensions are 90” wide by 96” to 132” long
  • Configuration can be used to fill van trailers from the rear.
  • Fills a 24′ wagon nicely.
  • Loader with at least 2100 lb lift capacity

Works With:

12 Bale Flat

Features:

The 12 Bale Flat System arranges the bales on their strings 4 wide and 3 long.
  • A popular choice for the models that put the bales on their strings.
  • Handles bales from 32” to 44” long
  • Bundle dimensions are 72” wide and 96” to 132”
  • This 12 Bale Flat System configuration fills a 20′ wagon nicely.
  • Same size group as the 1534 only the bales are left flat.
  • Loader with at least 1800 lb lift capacity

Works With:

10 Bale Flat

Features:

The 10 Bale Flat System arranges the bales on their strings 4 wide and 2 long, plus a tie row with 2 bales turned sideways.
  • Our most popular accumulator
  • The 10 Bale Flat System is well suited for small farms.
  • Handles bales from 32” to 38” long
  • Bundle dimensions are 64” to 76” wide and 82” to 94” long
  • The tie row allows for cross-stacking with the KN510F or 510F, making a more stable load on the wagon or truck.
  • The 2 1/2 bale length fills a 7.5 ft wagon from one side to the other
  • The low weight requirement for the grabber allows for the use of a smaller loader.
  • Loader with at least 1700 lb lift capacity

Works With:

8 Bale Flat

Features:

The 8 Bale Flat System arranges the bales on their strings 4 wide and 2 long.
  • Handles bales from 32” to 48” long
  • Bundle dimensions are 72” wide and can vary from 64” to 96” long
  • The 8 Bale Flat System is excellent for small farms.
  • The low weight requirement for the grabber allows for the use of a smaller loader.
  • If your bales are 36″ long, you can cross stack the bales with the 408 grabber.
  • Loader with at least 1400 lb lift capacity

Works With:

4 Bale Flat

Features:

The 4 Bale Flat System arranges the bales on their strings 4 wide and 1 long.
  • Handles bales from 32″ to 48″ long
  • Bundle dimensions are 72″ wide and length can vary, depending on bale dimensions.
  • The 4 Bale Flat System is the solution for hay production around 6,000 bales or less per year.
  • Can handle 14×18″ and 16×18″ bales from 32″ to 48″ long at whatever density is needed, with no adjustments.
  • The two bale length allows for narrower wagons or for longer bales than the models that arrange the bales 3 long.
  • If your bales are 36″ long, you can cross stack the bales with the EGF8 grabber.
  • The low weight requirement for the grabber allows for the use of a small loader.

Works With:

AE18 ACCUMULATOR

Features:

This accumulator arranges the bales on edge 6 wide and 3 long.
  • Our largest accumulator.
  • Good for filling van trailers from the rear.
  • Handles bales from 32” to 44” long
  • Bundle dimensions are 84” wide and 96” to 132” long
  • The 18 bale group has a 17% time savings advantage over the 15 bale as the grab contains 20% more bales, it reduces the number of packs by 17%.
  • This bale arrangement allows you to completely fill your 9’x24′ wagon.
  • Loader with at least 2200 lb lift capacity

AE15 ACCUMULATOR

Features:

This accumulator arranges the bales on edge 5 wide and 3 long.
  • Handles Bales from 32″ to 44″ long
  • Bundle dimensions are 70″ wide by 96″ to 132″ long
  • This bale arrangement allows you to completely fill your 9’x20′ wagon.
  • The 15 bale pack has a 33% time savings advantage over the 10 bale as the grab contains 50% more bales, it reduces the number of packs by 33%.
  • Loader with at least 1900 lb lift capacity

AE10 ACCUMULATOR

Features:

This accumulator arranges the bales on edge 5 wide and 2 long.
  • Handles bales from 32″ to 40″ long
  • Bundle dimensions are 75″ wide and 64″ to 96″ long
  • The AE10 accumulator is well suited for small farms.
  • The low weight requirement for the grabber allows for the use of a smaller loader.
  • If your bales are 36″ long, you can cross stack the bales with the KN510 or 510 grabber.
  • Loader with at least 1500 lb lift capacity

AE10 Working Dimensions: 17’4″ L x 7’10″″ W x 9’3″ H
AE10 Shipping Dimensions: 17’4″ L x 7’10″″ W x 5’7″ H
AE10 Weight: 2130 lbs

AF15 ACCUMULATOR

Features:

This accumulator arranges the bales on their strings 5 wide and 3 long.
  • Our largest configuration for bales on their strings.
  • Handles bales from 32” to 44” long
  • Bundle dimensions are 90” wide by 96” to 132” long
  • Configuration can be used to fill van trailers from the rear.
  • Fills a 24′ wagon nicely.
  • Loader with at least 2100 lb lift capacity

AF12 ACCUMULATOR

Features:

This accumulator arranges the bales on their strings 4 wide and 3 long.
  • A popular choice for the models that put the bales on their strings.
  • Handles bales from 32″ to 44″ long
  • Bundle dimensions are 72″ wide and 96″ to 132″
  • This configuration fills a 20″ wagon nicely.
  • Same size group as the 1534 only the bales are left flat.
  • Loader with at least 1800 lb lift capacity

AF10 ACCUMULATOR

Features:

This accumulator arranges the bales on their strings 4 wide and 2 long, plus a tie row with 2 bales turned sideways.
  • Our most popular accumulator
  • The 10 bale accumulator is well suited for small farms.
  • Handles bales from 32” to 38” long
  • Bundle dimensions are 64” to 76” wide and 82” to 94” long
  • The tie row allows for cross-stacking with the KN510F or 510F, making a more stable load on the wagon or truck.
  • The 2 1/2 bale length fills a 7.5 ft wagon from one side to the other.
  • The low weight requirement for the grabber allows for the use of a smaller loader.
  • Loader with at least 1700 lb lift capacity

AF8 ACCUMULATOR

Features:

The AF8 accumulator arranges the bales on their strings 4 wide and 2 long.
  • Our smallest accumulator.
  • Handles bales from 32″ to 48″ long
  • Bundle dimensions are 72″ wide and can vary from 64″ to 96″ long
  • The 8 bale accumulator is excellent for small farms.
  • The low weight requirement for the grabber allows for the use of a smaller loader
  • If your bales are 36″ long, you can cross stack the bales with the 408 grabber.
  • Loader with at least 1400 lb lift capacity

AF4 ACCUMULATOR

Features:

The AF4 accumulator arranges the bales on their strings, 4 wide and 1 long.
  • Our smallest accumulator.
  • Handles bales from 32″ to 48″ long
  • Bundle dimensions are 72″ wide and length can vary, depending on bale dimensions.
  • The AF4 4 bale accumulator is the solution for hay production around 6,000 bales or less per year.
  • Can handle 14×18″ and 16×18″ bales from 32″ to 48″ long at whatever density is needed, with no adjustments.
  • The two bale length allows for narrower wagons or for longer bales than the models that arrange the bales 3 long.
  • If your bales are 36″ long, you can cross stack the bales with the EGF8 grabber.
  • The low weight requirement for the grabber allows for the use of a small loader.

KN618 TIE-GRABBER

Features:

  • Good for filling van trailers from the rear.
  • This bale arrangement allows you to completely fill your 9’x24′ wagon.
  • The 18 bale group has a 17% time savings advantage over the 15 bale as the grab contains 20% more bales, it reduces the number of packs by 17%.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

KN618 Working Dimensions: 95″ L x 87.5″ W
KN618 Shipping Dimensions: 109” L x 95” W x 30” H
KN618 Weight: 1540 lbs

Requires:
Loader with at least 2600lb lift capacity*
One set of remotes with optional splitter. Two sets of remotes without the splitter.

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.

KN615 TIE-GRABBER

Features:

  • This bale arrangement allows you to completely fill your 9’x20′ wagon.
  • The 15 bale pack has a 33% time savings advantage over the 10 bale as the grab contains 50% more bales, it reduces the number of packs by 33%.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

KN615 Working Dimensions: 95″ L x 72″ W
KN615 Shipping Dimensions: 109” L x 78” W x 30” H
KN615 Weight: 1480 lbs

Requires:
Loader with at least 2400lb lift capacity*
One set of remotes with optional splitter. Two sets of remotes without the splitter.

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

KN510 TIE-GRABBER

Features:

  • The low weight requirement for the grabber allows for the usage of a smaller loader.
  • If your bales are 36″ long, you can cross stack the bales with the KN510 or 510 grabber.
  • The 1034 bale group can be picked up from any side of the group.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

KN510 Working Dimensions: 72″ L x 72″ W
KN510 Shipping Dimensions: 86” L x 78” W x 30” H
KN510 Weight: 1380 lbs

Requires:
Loader with at least 1800lb lift capacity*
One set of remotes with optional splitter. Two sets of remotes without the splitter.

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

KN615F TIE-GRABBER

Features:

  • Configuration can be used to fill van trailers from the rear.
  • Fills a 24′ wagon nicely.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

KN615F Working Dimensions: 95″ L x 87.5″ W
KN615F Shipping Dimensions: 109” L x 95” W x 30” H
KN615F Weight: 1515 lbs

Requires:
Loader with at least 2500lb lift capacity*
One set of remotes with optional splitter. Two sets of remotes without the splitter.

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

KN612F TIE-GRABBER

Features:

  • This configuration fills a 20′ wagon nicely.
  • Same size group as the 1534 only the bales are left flat.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

KN612F Working Dimensions: 95″ L x 72″ W
KN612F Shipping Dimensions: 109” L x 78” W x 30” H
KN612F Weight: 1460 lbs

Requires:
Loader with at least 2300lb lift capacity*
One set of remotes with optional splitter. Two sets of remotes without the splitter.

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

KN510F TIE-GRABBER

Features:

  • The square dimensions of this pack allow for cross-stacking.
  • Group can be picked up from the tie row end or the opposite end to enable cross-stacking
  • The low weight requirement for the grabber allows for the use of a smaller loader.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

KN510F Working Dimensions: 90” L x 72” W
KN510F Shipping Dimensions: 104” L x 78” W x 30” H
KN510F Weight: 1440 lbs

Requires:
Loader with at least 1900lb lift capacity*
One set of remotes with optional splitter. Two sets of remotes without the splitter.

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

KN408F TIE-GRABBER

Features:

  • The two bale length allows for narrower wagons or for longer bales
  • The square dimensions of this pack allows for cross-stacking.
  • The low weight requirement for the grabber allows for the use of a small loader.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

KN408F Working Dimensions: 72″ L x 72″ W
KN408F Shipping Dimensions: 86” L x 78” W x 30” H
KN408F Weight: 1280 lbs

Requires:
Loader with at least 1700lb lift capacity*
One set of remotes with optional splitter. Two sets of remotes without the splitter.

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

618 GRABBER

Features:

  • Good for filling van trailers from the rear.
  • This bale arrangement allows you to completely fill your 9’x24′ wagon.
  • The 18 bale group has a 17% time savings advantage over the 15 bale as the grab contains 20% more bales, it reduces the number of packs by 17%. contains 50% more bales, it reduces the number of packs by 33%.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

618 Working Dimensions: 95″ L x 87.5″ W
618 Shipping Dimensions: 105” L x 93.5” W x 22” H
618 Weight: 840 lbs

Requires:
Loader with at least 2200lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

615 GRABBER

Features:

    • This bale arrangement allows you to completely fill your 9’x20′ wagon.
    • The 15 bale pack has a 33% time savings advantage over the 10 bale as the grab contains 50% more bales, it reduces the number of packs by 33%.
    • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

    615 Working Dimensions: 95″ L x 72″ W
    615 Shipping Dimensions: 105” L x 72” W x 22” H
    615 Weight: 780 lbs

    Requires:
    Loader with at least 1900lb lift capacity*
    One set of remotes

    *Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

510 GRABBER

Features:

  • If your bales are 36″ long, you can cross stack the bales with the KN510 or 510 grabber.
  • The small group size has low requirements for loader size.
  • Compatible with similarly arranged groups from competitive accumulator brands.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

510 Working Dimensions: 72″ L x 72″ W
510 Shipping Dimensions: 82” L x 72” W x 22” H
510 Weight: 680 lbs

Requires:
Loader with at least 1500lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

615F GRABBER

Features:

  • Configuration can be used to fill van trailers from the rear.
  • Fills a 24′ wagon nicely.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

615F Working Dimensions: 95″ L x 87.5″ W
615F Shipping Dimensions: 105” L x 93.5” W x 22” H
615F Weight: 815 lbs

Requires:
Loader with at least 2100lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

612F GRABBER

Features:

  • This configuration fills a 20′ wagon nicely.
  • Same size group as the 1534 only the bales are left flat.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

612F Working Dimensions: 95″ L x 72″ W
612F Shipping Dimensions: 105” L x 72” W x 22” H
612F Weight: 760 lbs

Requires:
Loader with at least 1800lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

510F GRABBER

Features:

  • The square dimensions of this pack allows for cross-stacking.
  • Group can be picked up from the tie row end or the opposite end to enable cross-stacking
  • The low weight requirement for the grabber allows for the use of a smaller loader.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

510F Working Dimensions: 90” L x 72” W
510F Shipping Dimensions: 100” L x 72” W x 22” H
510F Weight: 740 lbs

Requires:
Loader with at least 1700lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

408F GRABBER

Features:

  • The two bale length allows for narrower wagons or for longer bales than the models that arrange the bales 3 long.
  • The square dimensions of this pack allows for cross-stacking.
  • The low weight requirement for the grabber allows for the use of a small loader.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

408F Working Dimensions: 72″ L x 72″ W
408F Shipping Dimensions: 82” L x 72” W x 22” H
408F Weight: 580 lbs

Requires:

Loader with at least 1400lb lift capacity*

One set of remotes *

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

EGF8 GRABBER

Features:

  • The two-bale length allows for narrower wagons or for longer bales than the models that arrange the bales 3 long.
  • Handles bales 32″ to 38″ long. If you want to do longer bales, one of our larger grabbers may be a better fit.
  • If your bales are 36″ long, you can cross stack the bales with the EGF8 grabber.
  • The low weight requirement for the grabber allows for the use of a small loader.
  • Available with universal skidsteer plate only.
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

EGF8 Working Dimensions: 72″ L x 68″ W x 9″ H
EGF8 Shipping Dimensions: 78″ L x 71″ W x 19″ H
EGF8 Working Weight: 440 lb

Requires:

Loader with at least 1150lb lift capacity*

One set of remotes *

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.*

205 COMPACT BALE GRABBER

Features:

  • Picks up 5 bales on edge
  • Ideal for compact loader tractors
  • Compatible with the 10 bale edge and 15 bale edge arrangements

205 Working Dimensions: 36”L x 72”W
205 Shipping Dimensions: 42”L x 72”W x 22”H
205 Weight: 340 lbs

Requires:
Loader with at least 750 lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.

NH618 – 18 BALE NH STACKWAGON GRABBER

Features:

  • Picks up 18 bales on edge
  • For NH Stackwagons that arrange 18 bales per layer (3 wide x 6 long)

NH618 Working Dimensions: 89”L x 102”W
NH618 Shipping Dimensions: 93”L x 103”W x 22”H
NH618 Weight: 890 lbs

Requires:
Loader with at least 2200 lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.

520 BALE GRABBER

Features:

  • Picks up 2 10 bale edge groups
  • Great for moving large quantities of bales

520 Working Dimensions: 72″L x 144″W
520 Shipping Dimensions: 82”L x 144”W x 22”H
520 Weight: 1400 lbs

Requires:
Loader with at least 3000 lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.

NH615 – 15 BALE NH STACKWAGON GRABBER

Features:

  • Picks up 15 bales on edge
  • For NH Stackwagons that arrange 15 bales per layer (3 wide x 5 long)
  • Working dimensions are inside the frame where bundles are carried but the bundles can vary in width and length.

NH615 Working Dimensions: 72”L x 102”W
NH615 Shipping Dimensions: 76”L x 103”W x 22”H
NH615 Weight: 830 lbs

Requires:
Loader with at least 1900 lb lift capacity*
One set of remotes

*Lift capacity is an estimate based on an average bale weight of 40-50 pounds. However, it is up to the individual to determine their specific loader requirements.

Top crossmenu linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram